Calco Poly Technik

Home / Materials / CiLON®

Polyamide 6 and 66

CiLON®

The engineering workhorse.

Tough, wear-resistant and heat-resistant, with glass-fibre reinforcement raising stiffness and strength and halving thermal expansion. Unfilled to 60% glass fibre, mineral and hybrid fillers, super-tough, heat-stabilised and flame-retardant.

Typical parts

Under-hood and structural automotive partsPower-tool housingsGearsCable tiesSwitchgear and connector housingsTextile-machinery parts

Polyamide 6

Polyamide 6 is the most widely specified engineering thermoplastic for good reason: toughness, wear resistance, chemical resistance and heat resistance in one easily moulded polymer. CiLON® PA6 grades add glass fibre, minerals and hybrid fillers: reinforced grades are up to 80% stiffer and 70% stronger than unfilled PA6, with roughly half the thermal expansion.

Compared with PA66, PA6 gives better surface finish, easier processing and higher impact strength at a lower melt temperature; PA66 gives higher stiffness and heat resistance.

What it offers

  • High stiffness, strength and dynamic fatigue resistance
  • Excellent impact and toughness, hot and cold
  • Very good abrasion and wear resistance
  • Good electrical properties
  • Excellent fuel, oil and grease resistance
  • Heat-stabilised, UV-stabilised, impact-modified, laser-markable and hydrolysis-resistant options
  • Colour-matched grades, including light colours
CiLON®PA6

710C0031A

PA6, unfilled, cable-tie grade

Typical parts: Cable ties

Natural
CiLON®PA6

710C2031 HFHS

PA6, 25–30% glass fibre, high flow, heat-stabilised

Typical parts: Engine covers, fan shrouds

High flowHeat-stabilisedNatural
CiLON®PA6

710C3031 / 710C3001

PA6, 30% glass fibre

Typical parts: Air intake manifolds, air filter housings, power-tool housings

Natural / black
CiLON®PA6

710C5031 / 710C5001

PA6, 50% glass fibre

Typical parts: Metal replacement, structural parts

Natural / black
CiLON®PA6

710C6031 / 710C6001

PA6, 60% glass fibre

Typical parts: Metal replacement, structural parts

Natural / black
CiLON®PA6

710C4101

PA6, 40% mineral filled, low warpage

Low warpageBlack
CiLON®PA6

710C3301

PA6, 15% glass fibre + 15% mineral hybrid

Balanced stiffness and warpageBlack

Design and processing notes.

Design to conditioned values

PA6 absorbs moisture in service, gaining toughness and losing stiffness. Validate parts conditioned to ISO 1110, not dry-as-moulded.

Mould reinforced grades hot

A mould at 80–90 °C improves crystallinity and hides fibre read-out on visible surfaces; cooler tools shorten cycle but raise post-shrinkage.

Hybrids for flat parts

Glass–mineral grades such as 710C3301 reduce differential shrinkage and warpage on flat, thin housings and covers.

Polyamide 66

Where the application runs hotter, stiffer and longer, polyamide 66 is the answer. Its higher melting point and crystallinity give better creep resistance, higher heat-deflection temperature and lower moisture-driven property change than PA6. CiLON® PA66 grades cover unfilled and super-tough materials through 60% glass fibre, with heat-stabilised, hydrolysis-resistant and high-flow variants for the engine bay.

Heat-stabilised (HS) grades are formulated for long-term thermal ageing; hydrolysis-resistant (HR) grades retain properties after ageing in hot glycol coolant.

What it offers

  • Highest stiffness and strength in the polyamide range
  • Continuous service at elevated temperature; HS grades for long-term ageing
  • Excellent creep and fatigue resistance
  • Very good wear resistance and sliding properties
  • Fuel, oil and coolant resistance; HR grades for glycol
  • High-flow grades for thin walls and long flow paths
CiLON®PA66

720C0001HS

PA66, unfilled, heat-stabilised

Typical parts: Cable ties on engine-bay routings

Heat-stabilisedBlack
CiLON®PA66

720C0031A

PA66, unfilled, cable-tie grade

Typical parts: Cable ties

Natural
CiLON®PA66

720C3004 HS

PA66, 30% glass fibre, heat-stabilised

Typical parts: Radiator end tanks, cooling pipes

Heat-stabilised
CiLON®PA66

720C3004 HSHD

PA66, 30% glass fibre, hydrolysis-resistant, heat-stabilised

Typical parts: Radiator end tanks, cooling pipes and connectors

Hydrolysis-resistantHeat-stabilisedBlack
CiLON®PA66

720C3031 HFHS

PA66, 30% glass fibre, high flow, heat-stabilised

Typical parts: Engine and cylinder-head covers

High flowHeat-stabilisedBlack
CiLON®PA66

720C3005HS

PA66, 35% glass fibre, heat-stabilised

Typical parts: Cylinder-head covers, under-hood structural parts

Heat-stabilisedBlack
CiLON®PA66

720C3002HFHS

PA66, 35% glass fibre, high flow, heat-stabilised

Typical parts: Thin-wall, laser-welded intake manifolds

High flowLaser weldable
CiLON®PA66

720C5031

PA66, 50% glass fibre

Typical parts: Metal replacement, structural parts

Natural
CiLON®PA66

720C6031

PA66, 60% glass fibre

Typical parts: Metal replacement, structural parts

Natural
CiLON®PA66

720C4101

PA66, 40% mineral filled, low warpage

Low warpageBlack

Design and processing notes.

A narrow melt window

PA66 melts near 260 °C and degrades above 300 °C: keep residence time short and purge on every stop.

HS above 120 °C

Specify heat-stabilised grades for continuous service above about 120 °C or where thermal ageing is specified.

Dry, then mould hot

Dry to 0.1% moisture and run glass-reinforced grades in an 80–100 °C mould; splay is the first sign of wet material.

Flame-retardant polyamide

Miniature circuit breakers, contactors, terminal blocks and wiring devices need a polymer that will not sustain a flame, resists tracking under voltage and holds its shape and strength through years of service. Flame-retardant polyamide grades are formulated for exactly that: unfilled and reinforced, in the greys and light colours the industry expects.

Grades are developed against UL 94, glow-wire (IEC 60695-2-12 and -13) and CTI (IEC 60112) requirements; ratings and test thicknesses are given on each grade's data sheet.

What it offers

  • UL 94 V-0 and V-2 rated grades
  • Glow-wire flammability index up to 960 °C
  • High tracking resistance
  • Mineral and glass–mineral fillers for low-warpage housings
  • Light and custom colours with narrow colour tolerance
CiLON®PA66

720C1001F

PA66, 15% glass fibre, flame retardant

Flame retardantBlack
CiLON®PA66

720C2001F

PA66, 20% glass fibre, flame retardant

Flame retardantBlack
CiLON®PA66

720C3001F / 720C3031F

PA66, 30% glass fibre, flame retardant

Typical parts: Contactor and relay housings

Flame retardantBlack / natural

FlamSaf® grades for breaker housings

Design and processing notes.

Ask for the rating at your wall

UL 94 and glow-wire results depend on thickness. Confirm the rating at the part's minimum wall.

Run at the low end

Flame-retardant packages narrow the processing window: keep melt temperature and residence time down, and avoid hot-runner dead spots.

Agree colour on the FR base

Flame-retardant fillers shift the base colour. Match greys and whites against a plaque of the FR grade, not the natural grade.

Typical starting conditions for injection moulding.

FamilyDryingMax. moistureMelt temperatureMould temperature
CiLON® / eCiLON® PA680 °C, 4–6 h≤ 0.10%240–270 °C60–90 °C
CiLON® / eCiLON® PA6680 °C, 4–6 h≤ 0.10%275–295 °C70–100 °C

Starting points for standard reinforced grades. The grade data sheet and, where issued, the product-specific processing sheet take precedence: flame-retardant, high-flow and alloy grades run in narrower windows.

Processing guidelines for every family

Try CiLON® on your own press.

A free 25 kg trial lot compounded on production lines, and a Calco engineer at your press.

Request a sample