730C0031 / 730C0032 / 730C0033
PBT, unfilled, three viscosity variants
PBT and PBT alloys
Dimensional precision and electrical performance.
Polybutylene terephthalate crystallises fast, absorbs very little water and holds its dimensions, which is why it is the polymer of choice for connectors, housings and precision parts that must fit the same way in a humid summer as in a dry winter.
Typical parts
Glass-reinforced ZiLITE® grades add high rigidity, mechanical and creep strength for parts under sustained load at elevated temperature; PBT/PET alloys add surface quality and stiffness.
Continuous use temperature is typically 115–135 °C, with short-term resistance to 150 °C; the melting point is around 225 °C.
What it offers
PBT, unfilled, three viscosity variants
PBT, unfilled
PBT, 15% glass fibre
PBT, 30% glass fibre
Typical parts: Connectors, sensor and relay housings
PBT, 35% glass fibre
PBT, 20% glass fibre, lamp-holder grade
Typical parts: Lamp holders and bases
PBT, 20% glass beads, low warpage
PBT/PET alloy, 20% mineral filled, high gloss
PBT/PET alloy, 30% glass fibre
PBT/PET alloy, 50% glass fibre
PBT crystallises fast; it demoulds earlier than PA66 at equal wall and is one of the easiest engineering polymers to mould consistently.
Long exposure to water above about 60 °C hydrolyses PBT. For hot-water or steam contact specify NovaLYN™ mPPE or PP instead.
PBT resists solvents, so it cannot be solvent-welded; design for ultrasonic, laser or hot-plate welding, or mechanical fastening.
Flame-retardant PBT combines the dimensional precision and electrical performance of polyester with UL 94 V-0 and glow-wire performance: the standard material for connector housings, relay and contactor bodies, lamp holders and appliance components that see voltage, heat and humidity together.
What it offers
PBT, unfilled, flame retardant
PBT, 30% glass fibre, flame retardant, two variants
Typical parts: Connector housings
PBT, 30% glass fibre, flame retardant
Typical parts: Connector, contactor and relay housings
PBT, 30% glass fibre, flame retardant, UL-listed
Typical parts: Contactor and switchgear housings
PBT, 30% glass fibre, flame retardant
Typical parts: Switchgear and MCCB housings
PBT, 30% glass fibre, flame retardant
Typical parts: Switchgear and MCCB housings
PBT, 30% glass fibre, flame retardant
Typical parts: Switchgear and MCCB housings
PBT, 30% glass fibre, flame retardant
Typical parts: Lamp holders, connector housings
PBT, 30% glass fibre, flame retardant, GM grade
PBT, 50% glass fibre, flame retardant
PBT hydrolyses in the melt if moulded wet, losing impact strength and molecular weight. Dry at 120 °C for 3–4 hours in dehumidified air and keep hopper residence short.
Where long, flat parts or connector housings warp, glass-bead grades and PBT/PET alloys give more isotropic shrinkage than glass fibre alone.
Higher mould temperatures raise crystallinity, surface gloss and dimensional stability; lower temperatures shorten cycle time at the cost of post-shrinkage.
| Family | Drying | Max. moisture | Melt temperature | Mould temperature |
|---|---|---|---|---|
| ZiLITE® PBT and alloys | 120 °C, 3–4 h | ≤ 0.04% | 240–260 °C | 60–100 °C |
Starting points for standard reinforced grades. The grade data sheet and, where issued, the product-specific processing sheet take precedence: flame-retardant, high-flow and alloy grades run in narrower windows.
A free 25 kg trial lot compounded on production lines, and a Calco engineer at your press.