Home / Automotive / Under the hood / Air filter housings
In production
Air filter housings
The problem this part has to solve, what usually goes wrong, and the grade we recommend.
The problem your part has to solve.
A large, thin-walled two-part housing that sits close to the engine and turbo, sees 90–120 °C and constant vibration, and is opened for every filter change over the life of the vehicle: hundreds of latch and hinge cycles on a part that also has to seal the filter element so dust cannot bypass it. It is cost-sensitive, often visible when the bonnet is open, and its long flow paths and thin walls test the moulder as much as the material.
Process: Injection moulding, snap-fit or hinged lid.
What usually goes wrong
- Latch and hinge fracture once the polymer has embrittled with heat ageing
- Warpage of the lid or base that lets dust bypass the filter seal
- Sink marks and fibre read-out on the visible surface; short shots at the end of long flow paths
- Rattle and resonance where a thin housing carries the intake duct
Our recommendation.
The baseline is CiLON® PA6 GF30, 710C3001 in black: stiff enough to hold the seal face flat, tough enough for the snap-fits, and easy to fill at PA6 melt temperatures. On engines where the housing sits over the turbo or exhaust side we recommend PA66 GF30, 720C3004, and where the specification calls for long-term heat ageing, PA66 GF30 HS, 720C3004 HSHD. For lids and covers that rely on a living hinge or deep snap-fits, unreinforced PA6, 710C0001 gives the elongation that glass-reinforced grades cannot. For high-volume black housings with no cosmetic requirement, eCiLON® PA6 GF30 is the cost option we will propose with the data to support it.
Why the Calco grade works
- Heat stabilisation so latches still flex after years at under-bonnet temperature
- Toughness and elongation matched to snap-fit and hinge geometry, not just stiffness
- Flow tuned for thin walls and long paths, with low fibre read-out on the visible skin
- Dimensional stability across humidity so the seal face stays flat
- Black grades with UV stabilisation for housings visible under the bonnet
Which grade, when.
| Choose when | Calco grade | Construction | Family | What it gives you |
|---|---|---|---|---|
| Standard housings and bases, visible under the bonnet | 710C3001 | PA6 GF30 | CiLON® | Stiffness for the seal, toughness for snap-fits |
| Lids and covers with hinges or deep snap-fits | 710C0001 | PA6 unfilled | CiLON® | Elongation and hinge life |
| Housings on the turbo or exhaust side | 720C3004 | PA66 GF30 | CiLON® | Higher service temperature |
| Long-term heat ageing in the specification | 720C3004 HSHD | PA66 GF30 HS | CiLON® | Aged toughness at the latch |
How we validate it with you.
Latch and hinge cycling
Open–close cycling on the moulded part dry, conditioned and after ageing, with latch retention force recorded.
Seal-face flatness
Flatness of the filter seal face measured at room temperature and after heat ageing, against the leak specification.
Vacuum and pressure
Collapse under intake vacuum and burst under boost on the assembled housing; resonance check on the duct.
More under the hood.
Air intake manifolds
Flange cracking after thermal cycling where weld lines and fibre orientation meet the bolt bosses.
OpenRadiator end tanks, cooling pipes and connectors
End-tank cracking at the crimp foot or hose spigot after coolant ageing.
OpenEngine covers and cylinder-head covers
Sink marks, fibre read-out and gloss variation on the visible engine cover.
OpenTry it on your own tool.
A free 25 kg trial lot compounded on production lines, and a Calco engineer at your press.
